Haier HW-C 1460 T

...and the assistant explained that Haier were huge in Asia and that they had experienced no returns on this product as yet. This was the cheapest model in the store, but it boasted many excellent features, such as: LED control Panel Triple A energy efficiency 11400 spin speed Many was progammes Quick wash of less that half an hour Delay start. When I first got the machine home and tried it, I was delighted. The quick wash is sufficient for ...
...it was very easy to use. The first point to note, is that the machine was VERY quiet. Even when it spins, it is rare to hear it when I am upstairs. It has an uneven load spin detector, which sometimes causes the machine to stop the spin, leaving clothes wet. I guess this is to stop the machine damaging itself, but can be a little frustrating. The controls are easy, but it can be difficult to see the LEDs in bright sunlight. To conclude, for the ...

boozecruise 03.08.2008 · Read full review
Ciao members have rated this review on average: helpful
Review of Haier HW-C 1460 T

Our landloard cursed us with this machine about a month ago. From the very first load it would not spin either at the end or during the wash meaning washing regularly came out soapy and soaked. After reporting it to comet for repair, they have replaced the PCB (programme control board) and it now appears to work correctly. It appears that these machines are being sold with a known fault in the PCB software that causes the machine to believe the ...
...may be possible to tell which version of the software your machine has. Before ours was "repaired" the ECO button had options for 1:3 1:2 3:4 and Full. After the new PCB was installed we were told this would change to L1, L2, L3, L4 and A which it has. If your machine has the old set of ECO options and it fails to spin regularly you definately need a replacement PCB. Even after the repair I do not like this machine very much. The wash options are ...

Wellsy2 17.08.2008 · Read full review
Ciao members have rated this review on average: helpful
Review of Haier HW-C 1460 T

If you have nothing better to do than try to balance your washing load so that it does not come out sopping wet, this is the machine for you. You'll have heaps of fun re-spinning your washing in the hope that after the 11ths spin cycle it 'might' come out damp enough to dry traditionally within 3-5 days. Even though technical support were very helpful and prompt answering the phone, thats not use when your washing is only half done. No more small washes with this machine as it will onlt spin when the drum is full. And guess what? Even when the drum is full, and it does manage to complete a spin cycle (not often) your washing will STILL come out wringing wet - might be an idea to purchase a separate spin dryer or better still and mangle - cos thats the only way you'll get damp washing with this baby! ...

Hedsta 03.08.2008
Ciao members have rated this review on average: helpful
Review of Haier HW-C 1460 T

I heard the sales spiel ' Established brand in other markets, excellent reliability, value for money, bound to go up in price as word spreads......' Wrong. It's a dog. A complete and utter, unadulterated lemon. Junk. It tangles clothes into a small hard ball every time there is anything like a pillowcase available. It washes poorly and, most annoying of all it NEVER completes a spin cycle first time - claiming that the load is unbalanced. It even does this when set off empty. I'm calling Comet out to it weekly in the hope that they'll get fed up and offer me a refund or a decent amount off a washing machine that does the job. Avoid it like the plague. ...

anorman 31.12.2008
Ciao members have rated this review on average: helpful
Review of Haier HW-C 1460 T

I work for Comet in the service department (fault reporting, booking engineers etc) and we have had no end of trouble with these appliances. Most of their washing machines are fitted with a faulty control board which stops the machine doing its final spin properly and shows UNB in the display - If you have this problem then its not normal and they will fix it for you! Hundreds of appliances have got this fault, we even stopped delivering them at one point! If youre thinking of buying one, some advice is: DONT! ...

summersun86 11.08.2008
Ciao members have rated this review on average: helpful
Review of Haier HW-C 1460 T

...had never actually heard of Haier washing machines before, but had a lot of fun bidding for it. I had already been told that appliances bought of an auction site, would probably have a bit of damage to them. When the machine arrived I found one small dint in the side, which when it was in situ couldn't be seen, so I was happy with it. The appearance of the machine is good, it is silver and fits in with any decor. There is quite a large range of ...
...speeds, the top one being 1400. The first wash I did I was extremely pleased with. I just used quick wash and the clothes came out clean and well spun. The next was I did was not a full load and when i got the clothes out they were absolutely dripping wet. I tried to spin them again and they still came out soaking. After a few attempts I found that the clothes will not spin properly unless there is a full load. This can be a good thing in some ways ...

Gabler 09.07.2008 · Read full review
Ciao members have rated this review on average: helpful
Review of Haier HW-C 1460 T

I purchased this wahing machine 11 months ago I have had the same problem with the spinner not working.As it was less than 1 year old the engineer from comet came out and said that this was a common fault and that the electronic programer which was originally fitted was too senstive and that they had now modified it. The new programmer was fitted and the problem seems to be resolved ...

pamphill 23.07.2008
Ciao members have rated this review on average: helpful
Review of Haier HW-C 1460 T

hi we have two haier washing machines both have trouble with the spin side of things, and to buy spares if your machine is out of warenty is just about imposible we have been trying to get two pcb for ages, nobody seems to stock them unless you are going to pay a fortune for a repair firm to come out and fix them. then the parts appear as if by magic. ...

trucks111 01.10.2008
Ciao members have rated this review on average: helpful
Review of Haier HW-C 1460 T

...loads and loads of these haier washing machines and what i can reveal is quite shocking 75% of these machines develop at least one fault within the first year most common being the pcb (printed circuit board) reseving a poor signal from the taco on the motor making the machine belleve it's unbaleneced this however isn't the only problem motor brushes WILL melt in some cases catch fire and finally the bearings are constantly failing, theres a reason ...

Paulio111 11.01.2009 · Read full review
Ciao members have rated this review on average: helpful
Review of Haier HW-C 1460 T

...were told in Currys that Haier are one of the leading manufacturers in Asia and that they produce high quality products. The machine itself is great looking, looks ultra modern and the controls are easy to use. There are lots of settings and it beeps when the cycle has completed and tells you the time remaining on the cycle. The drum seems quite small but you can still get a good load in. We have however found that ours isn't draining all the ...

Yummymummystacy 16.08.2008 · Read full review
Ciao members have rated this review on average: helpful
Review of Haier HW-C 1460 T

If you use the half load or 1/3 load the machine will not spin. Displays unbalanced. Apparently this is because the sensors are sensitive and according to the maker not a fault. Rubbish support ...

libramoon 02.06.2008
Ciao members have rated this review on average: somewhat helpful
Review of Haier HW-C 1460 T